Prosport Problem

no avatar
josh3rd
Posts: 16
Joined: Sat Jan 27, 2018 9:00 pm
Location: Berwyn, PA USA

Prosport Problem

Sun Dec 30, 2018 7:26 pm

Ok members, I have a .177cal Prosport. I hear something moving/sliding inside the shroud area. The area I’m talking about is like a 4-5 inch area from the breach to where the metal tapers down to the barrel/shroud sleeve. So when I tip the rifle forward and backwards out in front of me with the butt in my right hand and the tip of the barrel in my left and dip the barrel down and up (we'll call it shaking for time saving/writing) is when I hear something is rolling/sliding.
My Prosport is tuned by none other than our Prosport doctor Nitrocrushr, who did an awesome job. The spring guide and top hat were done by a man who needs no introduction, Motorhead. Nitrocrushr helped me by trying to eliminate possible problems one at a time. First I made sure that all screws were tight/secured, I removed the scope to eliminate that possibility and still heard the noise. I then removed the action from the stock and checked the cocking lever's 2 screws (1 attaches to comp tube and the other attaches the cocking lever to the action/bottom of rifle) and they were very secure. I shook it again and I still hear it. I removed the guts and checked the spring, the guide the top hat, piston seal, the transfer port, the compression tube (which I left inside and attached to the cocking lever) and nothing was broken, damaged and/or missing. But I still hear the noise. I opened up the cocking lever all the way and left the breach area open, shook it and still heard it. I thought at first that it might be the delrin washers in the piston but when I removed the piston, those washers did not move what so ever. I am wondering if it could be a fragment of a pellet possibly. If so, then how could that be? Then I looked into the barrel from the muzzle end. Wondering if a baffle or an O-ring got clipped. I shined a flashlight in both ends and could see the o-rings and no damage was noticed nor did I see any other debris or damage.
I am at a loss. She still shoots superb and I know you guys/gals will probably suggest to leave it alone but the sound bothers me. I don't know what it is or how to find out. I do not want to remove the shroud because I am afraid of damaging the finish or being unable to put it back. Air Arms, I believe, has a lifetime warranty through PA (I think) but if I send it to them, they may just want to replace the rifle. Now if that happens, then I got to replace the JM spring with the oem one, replace the Motorhead guide and top hat with the oem ones along with the comp tube that came with it. I will also be giving up a Nitrocrushr lapped and polished barrel along with his tuning of the trigger. So I am at odds of going the PA route. So any and all help would be greatly appreciated as to my situation.

no avatar
John814ce

Re: Prosport Problem

Sun Jan 13, 2019 9:31 pm

It sounds like a small piece of bond lock dried up and dropped off inside there maybe, the bond lock is used to set the shroud in place, try getting a small enough pipe to fit down the shrouded end and tape the other end of the pipe to the hover and block so it only sucks through the pipe, then try getting it down between the barrel and shroud tube, i know easier said than done. Or see ytube "air arms tx200 barrel removal " by Geoff bullock, tx200 barrel is fitted the same way as pro sport
Hope that helps

User avatar
pjgtech
Posts: 63
Joined: Sun May 07, 2017 5:06 pm

Re: Prosport Problem

Mon Jan 14, 2019 5:41 pm

Have you checked the scope, nothing loose on that? :)
pjgtech: BASC: SMK S2 Pistol .177
Air Arms ProSport .177 (Tuned):
Air Arms S410 TDR .177:
BSA R10 SE .177
Weihrauch HW 97KT. 22:(Tuned):
Weihrauch HW95 .177
Weihrauch HW40 .177
SMK Victory CP2 .177

User avatar
Blackbaronfish
Posts: 3364
Joined: Sun Feb 15, 2015 6:20 pm
Location: Nuneaton

Re: Prosport Problem

Mon Jan 14, 2019 7:29 pm

John814ce wrote:
Sun Jan 13, 2019 9:31 pm
It sounds like a small piece of bond lock dried up and dropped off inside there maybe, the bond lock is used to set the shroud in place, try getting a small enough pipe to fit down the shrouded end and tape the other end of the pipe to the hover and block so it only sucks through the pipe, then try getting it down between the barrel and shroud tube, i know easier said than done. Or see ytube "air arms tx200 barrel removal " by Geoff bullock, tx200 barrel is fitted the same way as pro sport
Hope that helps
Or a piece of a baffle. I had the same thing on a S410 extra

BBF
Did I mention that I'm the only one to have attended EVERY annual meet since we started

no avatar
John814ce

Re: Prosport Problem

Mon Jan 14, 2019 8:05 pm

Ye i think either way hes gonna are someone's gonna have to remove that shroud.

no avatar
josh3rd
Posts: 16
Joined: Sat Jan 27, 2018 9:00 pm
Location: Berwyn, PA USA

Re: Prosport Problem

Sat Jan 26, 2019 2:40 pm

Thanks everyone.I thinkbi should just let sleeping dogs lie. I, myself, don't want to remove the shroud a bigger something up.

Post Reply

Who is online

Users browsing this forum: No registered users and 13 guests