Page 1 of 1
S300 valve body
Posted: Mon Feb 26, 2018 8:34 pm
by Teggwynn
Hey all, newbie here to the forum! I have recently bought a early s300 and its bit of a project, its been leaking air for years and hence not been used. After stripping it down the valve seat in the body is dog rough and the cause of the issues, dont suppose anyone here would have one for sale please??
Matt
Re: S300 valve body
Posted: Mon Feb 26, 2018 8:41 pm
by eboswan
Welcome,Julian (BGALTD)will be along shortly too help you out.
Re: S300 valve body
Posted: Mon Feb 26, 2018 8:46 pm
by Teggwynn
Thanks bud
Re: S300 valve body
Posted: Tue Feb 27, 2018 12:06 pm
by bgaltd
Teggwynn wrote: āMon Feb 26, 2018 8:34 pm
Hey all, newbie here to the forum! I have recently bought a early s300 and its bit of a project, its been leaking air for years and hence not been used. After stripping it down the valve seat in the body is dog rough and the cause of the issues, dont suppose anyone here would have one for sale please??
Matt
good to speak to you Matt , fingers crossed we can get it sorted
.
Re: S300 valve body
Posted: Tue Feb 27, 2018 6:51 pm
by Teggwynn
bgaltd wrote: āTue Feb 27, 2018 12:06 pm
Teggwynn wrote: āMon Feb 26, 2018 8:34 pm
Hey all, newbie here to the forum! I have recently bought a early s300 and its bit of a project, its been leaking air for years and hence not been used. After stripping it down the valve seat in the body is dog rough and the cause of the issues, dont suppose anyone here would have one for sale please??
Matt
good to speak to you Matt , fingers crossed we can get it sorted
.
Thank you, pleasure to speak to someone with such a knowelge! Iāv had my orignal valve back from machine shop and they have done a peach of a job fair play. but and its a BIG but, where they have machined the valve face back perfect they have unearthed 4 very small hairline cracks around the hole the valve fits through. I can only assume that the cracks are from a issue during the orignal manufacture
Re: S300 valve body
Posted: Wed Feb 28, 2018 4:48 pm
by bgaltd
Teggwynn wrote: āTue Feb 27, 2018 6:51 pm
bgaltd wrote: āTue Feb 27, 2018 12:06 pm
Teggwynn wrote: āMon Feb 26, 2018 8:34 pm
Hey all, newbie here to the forum! I have recently bought a early s300 and its bit of a project, its been leaking air for years and hence not been used. After stripping it down the valve seat in the body is dog rough and the cause of the issues, dont suppose anyone here would have one for sale please??
Matt
good to speak to you Matt , fingers crossed we can get it sorted
.
Thank you, pleasure to speak to someone with such a knowelge! Iāv had my orignal valve back from machine shop and they have done a peach of a job fair play. but and its a BIG but, where they have machined the valve face back perfect they have unearthed 4 very small hairline cracks around the hole the valve fits through. I can only assume that the cracks are from a issue during the orignal manufacture
bugger
. you'll just have to send it to me for scrapping now
............
................. or we can adapt the 400 valve housing as discussed on the phone
. give me a ring if i can help .
rgds.
Julian
Re: S300 valve body
Posted: Fri Mar 02, 2018 9:00 pm
by Teggwynn
Little update, the valve body with the very small hairline cracks is sealing and holding air just perfect To my total suprise! The gun was charged to 200bar and left a few days and hadnt dropped a single psi..
what iām after is a multishot conversation now for it, would any body know if a s410 breach would fit?
Re: S300 valve body
Posted: Sat Mar 03, 2018 2:20 pm
by bgaltd
that i'm not sure about
.
