Huma s4"" reg DIY
Posted: Tue Oct 06, 2015 8:03 pm
Any fitted one ?
Do these need the bleed hole ?
What ave fps ?
Cheers
Chris
Do these need the bleed hole ?
What ave fps ?
Cheers
Chris
Page 1 of 2
Re: Huma s4"" reg DIY
Posted: Wed Oct 07, 2015 10:46 am
Huma,s site shows how to fit most if not all of their regs. Very helpful people. dave
Re: Huma s4"" reg DIY
Posted: Wed Oct 07, 2015 4:31 pm
Hi,
The fitting instructions (on Huma's website) shows the drilling of a vent hole. The fps is down to the set up of various aspects of the rifle's setup rather than the reg on its own.
Mark
The fitting instructions (on Huma's website) shows the drilling of a vent hole. The fps is down to the set up of various aspects of the rifle's setup rather than the reg on its own.
Mark
Re: Huma s4"" reg DIY
Posted: Wed Oct 07, 2015 6:02 pm
Cheers guys
I fitted a lane to my s400 and im happy, very happy indeed
Just thought I might try something else in my410 and thought the huma didnt need drilling
I fitted a lane to my s400 and im happy, very happy indeed
Just thought I might try something else in my410 and thought the huma didnt need drilling
Re: Huma s4"" reg DIY
Posted: Wed Oct 07, 2015 6:10 pm
The one that doesn't need drilling is the Altaros. I haven't fitted mine yet. The Huma and the Lane regs look like they work on the same principal as the Rapid reg in that they have an opposed piston, the vent hole allows the core to move freely.
Re: Huma s4"" reg DIY
Posted: Wed Oct 07, 2015 6:51 pm
Without sounding extreme I'm halfway through fitting an Alatros to my 510, real simple to do obviously but I had issues with real low power. It was under 9ftlbs 
I contacted alatros who did mail back about taking the sleeve out as some AA's are different ? Anyway took that out and had 14ftlbs
And since my last mail to them Ive had nothing, I'm also waiting for a few orings so I can try again
From what Ive experienced the Lane reg is awesome, I just wanted to test stuff back to back
I contacted alatros who did mail back about taking the sleeve out as some AA's are different ? Anyway took that out and had 14ftlbs
And since my last mail to them Ive had nothing, I'm also waiting for a few orings so I can try againFrom what Ive experienced the Lane reg is awesome, I just wanted to test stuff back to back
Re: Huma s4"" reg DIY
Posted: Thu Oct 08, 2015 7:49 am
32:1 wrote:... Anyway took that out and had 14ftlbs
hi,
Can you not just reduce it to sub 12 ft.lbs with the venturi screw? Sounds like you have removed anti-tamper.
Mark
Re: Huma s4"" reg DIY
Posted: Thu Oct 08, 2015 10:10 am
Yes anti tampers are removed to fit reg and service rifle, once I get this sorted Ill post results.
Interested in the huma as Ive heard good things, the alatros is a project in hand and we will see.
Cant see it bettering the lane reg in my s400 tbh
http://youtu.be/Ca4VMcZLDMI
Chris
Interested in the huma as Ive heard good things, the alatros is a project in hand and we will see.
Cant see it bettering the lane reg in my s400 tbh
http://youtu.be/Ca4VMcZLDMI
Chris
Re: Huma s4"" reg DIY
Posted: Thu Oct 08, 2015 3:23 pm
Just fitted the Altaros and I have 11.6 ft/lb average from 190 bar down to 100 bar. Variance is minimal, maybe 1/2 ft/lb so that will do me for now.
Re: Huma s4"" reg DIY
Posted: Thu Oct 08, 2015 6:45 pm
Brooksy wrote:Just fitted the Altaros and I have 11.6 ft/lb average from 190 bar down to 100 bar. Variance is minimal, maybe 1/2 ft/lb so that will do me for now.
That sounds good mate, simple install aren't they
Chris