tx200hc low power
- captbarb67
- Posts: 6
- Joined: Mon Jun 12, 2017 9:23 pm
tx200hc low power
Hi I have a mk2 tx200hc that was low on power so striped and re lube power was back up to 11.6 ft lbs but it's back down to 8.5ft lbs I've had it for about 20 years should I be replacing all the seals and piston or could it be something else.
- Blackbaronfish
- Posts: 3691
- Joined: Sun Feb 15, 2015 6:20 pm
- Location: Nuneaton
Re: tx200hc low power
I would be wanting to put in a new piston seal if it hasn't been done for twenty odd years....you owe it that at least
They do tend to form up a bit
BBF


They do tend to form up a bit
BBF
Did I mention that I'm the only one to have attended EVERY meet since we started
- gary martin
- Posts: 815
- Joined: Thu Feb 19, 2015 8:21 pm
Re: tx200hc low power
Blackbaronfish wrote:I would be wanting to put in a new piston seal if it hasn't been done for twenty odd years....you owe it that at least![]()
![]()
They do tend to form up a bit
BBF
I would add breach seals too.
- captbarb67
- Posts: 6
- Joined: Mon Jun 12, 2017 9:23 pm
Re: tx200hc low power
Okay will do that do I need to measure spring length as well and where is the best place to get these seal from.
- Blackbaronfish
- Posts: 3691
- Joined: Sun Feb 15, 2015 6:20 pm
- Location: Nuneaton
Re: tx200hc low power
Julian Bond the site owner. You will find a thread in the sales section
BBF
BBF
Did I mention that I'm the only one to have attended EVERY meet since we started
- captbarb67
- Posts: 6
- Joined: Mon Jun 12, 2017 9:23 pm
Re: tx200hc low power
Okay will do all apart and polished up
- captbarb67
- Posts: 6
- Joined: Mon Jun 12, 2017 9:23 pm
Re: tx200hc low power
I have a different piston seal on my rifle than the original it's a solid ptfe that screws onto the piston 25mm diameter 7mm long
does any body know where I can purchase one of these I have contacted Julian about the parts but no response yet.
does any body know where I can purchase one of these I have contacted Julian about the parts but no response yet.
- captbarb67
- Posts: 6
- Joined: Mon Jun 12, 2017 9:23 pm
Re: tx200hc low power
I have a different piston seal on my rifle than the original it's a solid ptfe that screws onto the piston 25mm diameter 7mm long
does any body know where I can purchase one of these I have contacted Julian about the parts but no response yet.
does any body know where I can purchase one of these I have contacted Julian about the parts but no response yet.
Re: tx200hc low power
Hi Guys I'd be interested to know what peoples mk3 HCs are cronographing at. Mine is almost new. I've only put about 700 pellets through it. I use AA Fields @16grains on the two separate occasions its registered 10.6 and 10.3 which I thought was a bit on the low side ...... especially as my mates new BSA Lightning was 11.0 !!! ... I wasn't happy !
)
Your thoughts etc would be appreciated
Cheers
Roj

Your thoughts etc would be appreciated
Cheers
Roj
Re: tx200hc low power
Roj 252 wrote:Hi Guys I'd be interested to know what peoples mk3 HCs are cronographing at. Mine is almost new. I've only put about 700 pellets through it. I use AA Fields @16grains on the two separate occasions its registered 10.6 and 10.3 which I thought was a bit on the low side ...... especially as my mates new BSA Lightning was 11.0 !!! ... I wasn't happy !)
Your thoughts etc would be appreciated
Cheers
Roj
The difference between 10.6 and 11.0 is only a few fps so I wouldn't worry. If it's accurate leave well alone. Try a lighter pellet such as AA Field Express.
Who is online
Users browsing this forum: No registered users and 54 guests