S400

no avatar
eric83
Posts: 6
Joined: Thu Feb 22, 2018 4:20 pm

S400

Wed Jan 22, 2020 1:52 pm

Tried putting a pellet in (177) and the bolt needed more force than normal to close ,tried firing and no pellet ! Put my brass cleaning rod down and eventually the pellet came out mangled ! Put another in same result , cleaned with brass brush and pull through tried again same result ! Anyone any idea ?

no avatar
143granville
Posts: 263
Joined: Mon Apr 03, 2017 8:15 pm
Location: barwell leicestershire .

Re: S400

Wed Jan 22, 2020 7:19 pm

hi is full of air ?
if so hammer sping .
leaking oring worth a check put pellet in
put tissue over the breach and fire if the
paper blows off .
BGLTD is the guy to message great guy .

no avatar
Roger5
Posts: 1071
Joined: Sat Jul 25, 2015 8:04 am
Location: Hampton middlesex

Re: S400

Wed Jan 22, 2020 7:54 pm

eric83 wrote:
Wed Jan 22, 2020 1:52 pm
Tried putting a pellet in (177) and the bolt needed more force than normal to close ,tried firing and no pellet ! Put my brass cleaning rod down and eventually the pellet came out mangled ! Put another in same result , cleaned with brass brush and pull through tried again same result ! Anyone any idea ?
What pellets you using?
And are you just rolling them into the tray, and then pushing them home with the bolt?
Or are you pushing them into the breech yourself?

no avatar
eric83
Posts: 6
Joined: Thu Feb 22, 2018 4:20 pm

Re: S400

Wed Jan 22, 2020 10:48 pm

Plenty of air , place pellets in as far as poss ! It’s as if something is in breech ? I’ve used this gun for a couple of years and shot hundreds of pigeons etc . Always cleaned when needed to keep accurate ! Looks like a complete strip and remove the breech and see what’s in ?

no avatar
eric83
Posts: 6
Joined: Thu Feb 22, 2018 4:20 pm

Re: S400

Wed Jan 22, 2020 10:53 pm

Sorry , being rude ! thanks for the reply’s 😀

no avatar
Roger5
Posts: 1071
Joined: Sat Jul 25, 2015 8:04 am
Location: Hampton middlesex

Re: S400

Thu Jan 23, 2020 8:48 am

eric83 wrote:
Wed Jan 22, 2020 10:48 pm
Plenty of air , place pellets in as far as poss ! It’s as if something is in breech ? I’ve used this gun for a couple of years and shot hundreds of pigeons etc . Always cleaned when needed to keep accurate ! Looks like a complete strip and remove the breech and see what’s in ?
Shine a torch from the breech and have a peek down the barrel, all precautions safety wise being taken ( said before anyone else does ) Rog

User avatar
Blackbaronfish
Posts: 3690
Joined: Sun Feb 15, 2015 6:20 pm
Location: Nuneaton

Re: S400

Thu Jan 23, 2020 7:34 pm

Make sure the hammer rail is clean and your getting a good strike on the valve. Also have a look into the breech to see if the o'ring is still in position.

BBF
Did I mention that I'm the only one to have attended EVERY meet since we started

no avatar
eric83
Posts: 6
Joined: Thu Feb 22, 2018 4:20 pm

Re: S400

Thu Jan 23, 2020 8:49 pm

👍👍👍

no avatar
Jammy13
Posts: 43
Joined: Tue Jul 02, 2019 5:00 pm
Location: Northumberland

Re: S400

Fri Jan 24, 2020 6:55 pm

Eric,
if any of the above suggestions don't work, the problem is most likely to be the barrel has slipped partly out of the brass breach and moved slightly forward. The breach and the barrel have to be removed, cleaned of the existing glue(?), and refitted. I use blue Loctite sparingly. Be careful and watch for any Loctite that may have squeezed into the barrel bore and wipe off any excess on the outside of the breach. It should then be left for a while to set before refitting. Others may use something other than Loctite. It's worth fitting a new breach seal when it's apart.

This can happen if the rifle is repeatedly picked up by the barrel.

Keith

no avatar
poguemahone
Posts: 688
Joined: Sun Feb 15, 2015 10:36 am
Location: stoke

Re: S400

Sat Jan 25, 2020 11:19 am

o ring, they can get damaged, or even disappear ;)

Post Reply

Who is online

Users browsing this forum: No registered users and 20 guests