Air Arms S200 Firing Pot

no avatar
jimsdub
Posts: 3
Joined: Wed Aug 08, 2018 3:00 pm

Air Arms S200 Firing Pot

Wed Aug 08, 2018 3:10 pm

Can anyone advise on this topic. In cleaning my air reservoir I forgot to reinstall the firing pot or 'Stove pipe regulator' as some call it. I charged the cylinder and is holding pressure at 190 Bar. Can I dry fire without the pot to empty cylinder and refit pot? Simply concerned about full 190 Bar hitting the valve each time.
in the past some pcp's never had these flow restrictor 'regulators' . Any comments appreciated.

User avatar
Blackbaronfish
Posts: 3690
Joined: Sun Feb 15, 2015 6:20 pm
Location: Nuneaton

Re: Air Arms S200 Firing Pot

Wed Aug 08, 2018 6:53 pm

What type of filler have you got. The older sort can have a five pence piece inserted into the cap and screwed in until the air comes out on a steady flow

BBF
Did I mention that I'm the only one to have attended EVERY meet since we started

User avatar
Blackbaronfish
Posts: 3690
Joined: Sun Feb 15, 2015 6:20 pm
Location: Nuneaton

Re: Air Arms S200 Firing Pot

Wed Aug 08, 2018 7:01 pm

You could also loosen the fill valve a little

BBF
Did I mention that I'm the only one to have attended EVERY meet since we started

no avatar
jimsdub
Posts: 3
Joined: Wed Aug 08, 2018 3:00 pm

Re: Air Arms S200 Firing Pot

Wed Aug 08, 2018 7:44 pm

Thanks for replies. Never understood why they stopped selling those degassing tools in UK. Fill valve is an altaros gauge/manometer. Hammer strike pin does not protrude at all. Looks like loosening the gauge/fill assy a fraction is the only route open. Don't like messing with HPA without the proper tools, used to work in that field and experienced mishaps first hand to be wary enough.

User avatar
Blackbaronfish
Posts: 3690
Joined: Sun Feb 15, 2015 6:20 pm
Location: Nuneaton

Re: Air Arms S200 Firing Pot

Wed Aug 08, 2018 8:03 pm

Quite right. You don’t want anything going wrong with them pressures

BBF
Did I mention that I'm the only one to have attended EVERY meet since we started

no avatar
Roger5
Posts: 1071
Joined: Sat Jul 25, 2015 8:04 am
Location: Hampton middlesex

Re: Air Arms S200 Firing Pot

Wed Aug 08, 2018 8:27 pm

Raj suggests pushing the firing valve down onto a marble, it does work ;) Rog

no avatar
jimsdub
Posts: 3
Joined: Wed Aug 08, 2018 3:00 pm

Re: Air Arms S200 Firing Pot

Wed Aug 08, 2018 9:48 pm

Logical, marble or ball bearing in vice, I will try that, thanks.

no avatar
tonyc
Posts: 376
Joined: Mon May 29, 2017 10:55 am

Re: Air Arms S200 Firing Pot

Wed Aug 08, 2018 10:33 pm

Not sure if you understand the pot doesn't reduce the maximum pressure on the valve but restricts the rate of air flow. However, without the pot, the valve will snap shut more quickly (=more impact energy) and I guess that's the concern.

If the marble doesn't work, this may (or may not) be helpful!
My S400 pot fell off - the glued on section that is - a few shots after a refill. Discussed this with AA then emptied by firing as normal - no after effects. Did I read there was a problem with early S200 valves extruding? I'd check with AA first.

no avatar
TenMetrePeter
Posts: 1043
Joined: Wed Jun 29, 2016 5:40 pm
Location: Luton Beds UK

Re: Air Arms S200 Firing Pot

Thu Aug 09, 2018 12:46 pm

I take it there is no valve spring either?

Post Reply

Who is online

Users browsing this forum: No registered users and 15 guests