Search found 46 matches
- Mon Sep 26, 2016 6:17 pm
- Forum: TECHNICAL
- Topic: HELP Please TX200 Mk1 problem
- Replies: 6
- Views: 4159
Re: HELP Please TX200 Mk1 problem
glad to be of help. It's not uncommon to get the 'shiny stripe where the comp tube rubs. Pro Sports have a delrin bearing which prevents the problem. The rust spots on the comp tube (hardened steel) and the burr are almost exactly the same as what happened to me. When I stripped it all down the pist...
- Mon Sep 26, 2016 6:48 am
- Forum: TECHNICAL
- Topic: HELP Please TX200 Mk1 problem
- Replies: 6
- Views: 4159
Re: HELP Please TX200 Mk1 problem
or the scope mount 'recoil' pin has been screwed too far into the cylinder.
- Sun Sep 25, 2016 5:58 pm
- Forum: TECHNICAL
- Topic: HELP Please TX200 Mk1 problem
- Replies: 6
- Views: 4159
Re: HELP Please TX200 Mk1 problem
It may be caused by galling inside the cylinder. The rear end of the compression tube is pushed upwards to ride along the cylinder wall when you cock the rifle. This caused a 'grinding' sound in my first TX (also a MK1) When I stripped it down there was a worn stripe opposite and clearly visible thr...
- Sun Sep 25, 2016 8:55 am
- Forum: TECHNICAL
- Topic: Top Sear problems
- Replies: 9
- Views: 5094
Re: Top Sear problems
2. The TX sear is holding back the mainspring whereas the S400 etc is only holding back the hammer spring so maybe safety is a concern. They are just being careful I guess. and they are a manufacturer not a retailer. I know they are not a retailer but middle sears are widely available for £12,50 fr...
- Sat Sep 24, 2016 7:53 pm
- Forum: TECHNICAL
- Topic: Top Sear problems
- Replies: 9
- Views: 5094
Re: Top Sear problems
A while ago I started a thread, on another forum, regarding my friend's TX200 top sear. The contact point where it latches to the piston rod has been damaged/worn. Air Arms were contacted asking for advice and a receipt e-mail was just 'spares can be found at the following suppliers' No request for ...
- Sun Aug 28, 2016 8:01 pm
- Forum: TECHNICAL
- Topic: air arms Tx200MK3 loss of power
- Replies: 0
- Views: 1681
Re: air arms Tx200MK3 loss of power
It sounds to me like you have done no harm at all. If the spring was compressed for 2 weeks and is still 220mm then that's fine. As it is making slightly more power with lighter pellets it may be slamming slightly if you have any metal washers in the piston you could try taking one out and adding th...
- Sun Aug 21, 2016 9:36 pm
- Forum: Spring guns and tuning
- Topic: New Pro Sport Sometimes it will fire and sometimes it won't
- Replies: 13
- Views: 6949
Re: New Pro Sport Sometimes it will fire and sometimes it wo
It is likely that the oil/grease that AA use in the trigger unit is affecting the operation of the cocking/safety button. Maybe the stuff they use is good for transportation/storage but it leaves the sears discoloured and slow as it becomes sticky. I have stripped several TXs and Pro Sports and they...
- Sat Aug 06, 2016 10:28 pm
- Forum: AirArms Spares ( bgaltd )
- Topic: TX200 trigger parts
- Replies: 1
- Views: 2916
Re: TX200 trigger parts
Thanks for the info. Will try Air Arms to see if they can help.
- Sat Aug 06, 2016 6:12 pm
- Forum: AirArms Spares ( bgaltd )
- Topic: TX200 trigger parts
- Replies: 1
- Views: 2916
TX200 trigger parts
I am looking for a top sear for the TX unit.
My friend's has a small amount of damage where the piston rod latches and I don't want him to risk it
My friend's has a small amount of damage where the piston rod latches and I don't want him to risk it
- Sun Jul 03, 2016 7:04 pm
- Forum: Spring guns and tuning
- Topic: TX200 SR
- Replies: 4
- Views: 7370
Re: TX200 SR
They are relatively easy to service at home. Just a bit more fiddly than a standard TX and re-assembly must be done in a specific order. Chrono before you dismantle as they are very efficient and can easily go over 12ft/lb You learn a lot about a springer if you do it yourself and save money The Nyl...