Search found 11 matches

by Phil S
Sun Oct 04, 2020 8:39 am
Forum: TECHNICAL
Topic: S200 dumping air
Replies: 3
Views: 2726

Re: S200 dumping air

Problem sorted putting it through a cronograph it had been wound up to just under 20 ftlb and had flared the back end of the firing pin. New pin,spring and c clip and now reset to 11.4 ftlb. If you get a rifle or pistol second hand please check its power. I could have been in deep trouble had it bee...
by Phil S
Tue Sep 29, 2020 8:21 am
Forum: AirArms Spares ( bgaltd )
Topic: AIR ARMS 410 .22
Replies: 7
Views: 6336

Re: AIR ARMS 410 .22

I have ordered parts from John knibbs in Birmingham as no reply from AA spares on here.
Phil
by Phil S
Sat Sep 26, 2020 6:49 pm
Forum: AirArms Spares ( bgaltd )
Topic: S200 spares
Replies: 0
Views: 14029

S200 spares

Hi,
Are you supplying parts at the moment please.
Thanks Phil
by Phil S
Sat Sep 26, 2020 2:16 pm
Forum: TECHNICAL
Topic: S200 dumping air
Replies: 3
Views: 2726

S200 dumping air

Hi All, My new to me, but lived in s200 dump its air from time to time. The problem being that the firing pin sticks in the forward position and so holds the valve in the cylinder open. On taking it apart I find the C clip that should be on the inner end of the firing pin (42) sitting above the trig...
by Phil S
Sun Sep 20, 2020 7:32 am
Forum: TECHNICAL
Topic: S200 10 shot conversion
Replies: 2
Views: 2166

Re: S200 10 shot conversion

All now sorted.
Instructions arrived from AA
After much adjusting mag cycles ok.
Found tapping loaded mag face down on a hard surface seated pellet skirt on 0 ring and no jams so far.
Phil
by Phil S
Fri Sep 18, 2020 8:11 am
Forum: TECHNICAL
Topic: S200 10 shot conversion
Replies: 2
Views: 2166

S200 10 shot conversion

Hi All, New to me my s200 has a 10 shot conversion fitted. Most of the time it works OK but on occasion it fails to rotate No instructions with it on private purchase, requested from AA but no joy, Not good customer service Any help, suggestions please. 3 genuine mags and none better than the other,...
by Phil S
Fri Sep 04, 2020 3:42 pm
Forum: TECHNICAL
Topic: Air leaking
Replies: 5
Views: 2749

Re: Air leaking

The minute he thought he could see a profit for doing nothing, I bet it would have gone out theback for half an hour and cost me £150 plus to do what I did. They may offer a lifetime service on new guns bought from them, but like many shops get a bit greedy when they think you have little or no know...
by Phil S
Thu Sep 03, 2020 8:45 pm
Forum: TECHNICAL
Topic: Air leaking
Replies: 5
Views: 2749

Re: Air leaking

Think I may have solved my own problem Removed the air cylinder and it filled OK, so it was the firing pin holding it open. Think the pin had stuck in the fire position as it had cycled on a cylinder with no air in. So message to all keep a rough shot count and refill the cylinder before it is empty...
by Phil S
Thu Sep 03, 2020 3:38 pm
Forum: TECHNICAL
Topic: aa s200
Replies: 11
Views: 6452

Re: aa s200

I am currently in a similar position ,
Who can I ask for help/advice as only just joined the forum as only just got the s200.
Thanks Phil
by Phil S
Thu Sep 03, 2020 3:10 pm
Forum: TECHNICAL
Topic: Air leaking
Replies: 5
Views: 2749

Air leaking

His All, New to the forum as new to Air Arms. Picked an S200 up yesterday, had air in it, so today put 30 or so .177 pellets through it. Ran out of air. So connected the T filling adaptor, coked gun, opened the valve on the top of the filling bottle, with the bleed screw closed. Gauge goes up to 190...